Toshiba Launches Brushless Motor Pre-Driver IC for Automotive EPS

TOKYO — (BUSINESS WIRE) — August 27, 2015Toshiba Corporation (TOKYO:6502) today announced the launch of “TB9081FG”, a brushless motor [1] pre-driver IC enhanced to achieve functional safety[2], for use in electric power steering systems (EPS). Sample shipments will start on September 1st, 2015, with mass production scheduled to start in August, 2017.

This Smart News Release features multimedia. View the full release here: http://www.businesswire.com/news/home/20150827005402/en/

Toshiba: a brushless motor pre-driver IC "TB9081FG" for electric power steering systems(EPS) (Photo: ...

Toshiba: a brushless motor pre-driver IC "TB9081FG" for electric power steering systems(EPS) (Photo: Business Wire)

More and more safety-critical automotive systems, such as EPS, are required to meet the requirements of ASIL-D[3], the highest automotive safety integrity level prescribed in ISO 26262, “Road Vehicles – Functional Safety.”

The new IC integrates key main functions, including 3-phase pre-driver circuits [4], fail-safe relay pre-driver circuits [4] and motor current detection circuits [5], plus various failure detection circuits. An initial diagnosis circuit to detect latent faults in the failure detection circuits is also incorporated to secure higher functional safety.

Toshiba has also carried out a range of functional safety analyses to simulate various system failures and will provide customers with documentation, such as FMEDA[6], to support safety analysis and design.

Key Features

1. Failure detection circuits for functional safety
Built-in VB over/under voltage detection circuit, VCC over/under voltage detection circuit, over temperature detection circuits, and short detection circuits [7].

2. Diagnosis circuit for failure detection circuits for functional safety
A built-in diagnostic circuit in the failure-detection circuit detects any latent faults.

3. Built-in fail-safe relay pre-driver circuits
Built-in fail-safe relay pre-driver circuits drive the semiconductor relay connected between the motor and MOSFET (driver) and between the power-supply side and MOSFET (driver). The fail-safe relay pre-driver circuit has a total of 5ch, three for the motor side and two for the power-supply side. Both have dedicated input terminals, making independent control possible.

4. Under voltage operation
Voltage drop caused by cranking after idling reduction is accommodated by improving battery operation voltage range down to 4.5V (min.).

5. Pre-Driver operation is selectable on failures detection.
Customers can set the system to respond to detected failures in one of two ways, using the input setting of the SPI communication [8]. One setting uses this new IC to stop the external MOSFET, the other switches to external control of the MOSFET using the MCU (Micro Controller Unit). Selection can be made according to the customer’s application or system, and for various systems.

 

Main Specifications

Part Number   TB9081FG
Mass Production August, 2017
Mass Production Volume 1 million units per year
Pre-driver channels

11 channels

(high side: 3 ch, low side: 3 ch, fail-safe side: 5ch)

Operating

Voltage Range

+ 4.5 to 18V
Operating Temperature Range -40 to 125°C
Pre-driver input signal Made for a direct control
Detection Circuits VB over/under voltage detection circuit, VCC over/under voltage detection circuit, over temperature detection circuits, and short detection circuits
Motor Current Detection Circuits Converts motor current to voltage and output to MCU
Package   LQFP64-P-1010-0.50E

(12.0mm × 12.0mm × 1.6mm)


1 | 2  Next Page »
Featured Video
Jobs
Senior Firmware Architect - Server Manageability for Nvidia at Santa Clara, California
Sr. Silicon Design Engineer for AMD at Santa Clara, California
GPU Design Verification Engineer for AMD at Santa Clara, California
Design Verification Engineer for Blockwork IT at Milpitas, California
CAD Engineer for Nvidia at Santa Clara, California
Senior Platform Software Engineer, AI Server - GPU for Nvidia at Santa Clara, California
Upcoming Events
SEMICON Europa 2024 at Messe München München Germany - Nov 12 - 15, 2024
DVCon Europe 2023 at Holiday Inn Munich – City Centre Munich Germany - Nov 14 - 15, 2024
SEMI MEMS & Imaging Sensors Summit, at International Conference Center Munich Germany - Nov 14, 2024
SEMI | MSIG MEMS & Imaging Sensors Summit at Munich Germany - Nov 14 - 15, 2024



© 2024 Internet Business Systems, Inc.
670 Aberdeen Way, Milpitas, CA 95035
+1 (408) 882-6554 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering TechJobsCafe - Technical Jobs and Resumes GISCafe - Geographical Information Services  MCADCafe - Mechanical Design and Engineering ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy PolicyAdvertise