Amber FX is built on top of the Amber™ Analyzer, introduced in May 2007 as the industry’s highest performance and capacity STA platform. It merges the performance of the Amber fully threaded, incremental analysis architecture with the accuracy of a new generation FX transistor model (FXM). The result is near SPICE-level accuracy for timing delay and process variance, both of which are critical factors in the transition to 45 and 40-nanometer (nm) semiconductor processes. Amber FX is immediately available in two complementary modules, Amber FX Transistor STA and Amber FX Transistor SSTA, and is supported in the TSMC Reference Flow 9.0.
“Amber FX is the first STA and SSTA solution that combines performance, accuracy, and variance-aware timing in the same analysis,” said Isadore Katz, president and CEO of CLK Design Automation. “Every other solution is a compromise. You can look at variance, but without accuracy, or visa versa — all with painfully slow results. Amber FX provides near-SPICE accuracy for delay and variance combined with threaded performance. Amber FXM libraries are the only solution, other than SPICE itself, which can deliver the latest data from the foundry to the designer the very same day.”
CLK Design Automation will debut the Amber FX Analyzer at the 45th Design Automation Conference to be held June 9-12, 2008 in Anaheim, Calif. Attendees can see the Amber and CLKWorks product overview in Booth #2667 or email Email Contact to pre-arrange for private demonstration.
Highly Accurate Transistor Modeling
Manufacturing variance is one of the biggest barriers to successful adoption of advanced 45-nm and 40-nm process nodes. Although the expectation is that these nodes will deliver much better speed and power at a lower cost per die, traditional corner-based timing closure methodologies are much too pessimistic and make timing closure very difficult. Statistical timing tools and new library formats such as CCSM and ECSM are supposed to address these problems. However, these tools and models are slower than their predecessors, and generating libraries can take weeks, causing them to be out of sync with the latest foundry data.
Amber FX removes these barriers with a FX transistor model that captures delay and variance directly from SPICE, the foundry SPICE model, and the SPICE netlists for each of the cells. The Amber FXM library is a cell-level library that includes all of the transistors and parasitics for each cell. Amber FXM has been qualified with TSMC 65-nm and 40-nm libraries using Berkeley SPICE and HSPICE™ for characterization. FXM is an extension to the Liberty format and addresses a large number of known accuracy problems in existing Liberty, ECSM, and CCSM libraries. It handles a wide range of high-risk timing behaviors that are not properly modeled by other timing solutions, such as multiple input switching, non-linear input slopes, voltage drop, functional noise, etc.
Industry’s First TSSTA Solution
In addition to the FXM model, Amber FX’s unique approach to TSSTA is enabled by its fast SPICE analysis engine and architectural-level integration with the Amber platform for a seamless flow from STA through SSTA. This provides both Amber FX STA and SSTA users with all of the Amber performance and capabilities, including 10x speed-ups via threading and 100x throughput improvements for incremental operations, multi-mode/multi-corner analysis and debug, and signal integrity analysis.
Amber FX Transistor STA is used for block and full-chip transistor timing and signal integrity analysis. It uses the FXM model to perform STA with traditional corners for very high accuracy timing, and allows users to combine non-linear delay models with transistor models. Amber FX Transistor SSTA is used for path-based TSSTA with the FXM model. Corners are replaced with a statistical distribution for the timing, which represents the potential manufacturing variance as tracked and analyzed by the foundry. Users first complete a baseline static timing run and then select a set of paths for full transistor-level SSTA. The nominal delay and variance of these paths is then recalculated using the FXM model and delay calculator. For the purposes of reporting, the variance is treated as a normal distribution so timing can be assessed at multiple points.
Pricing & Availability
Amber FX Transistor STA and Amber FX Transistor SSTA are shipping today for 32-bit and 64-bit Linux computing platforms. The U.S. list price for a one-year license is $150,000 for Amber FX STA and $150,000 for Amber FX SSTA.
About CLK Design Automation
CLK Design Automation, Inc. develops and markets timing closure solutions used in the design of high-performance microprocessor and advanced semiconductors. Its fully threaded, incremental architecture enables the CLK Amber SA to execute 10 to 100x faster than conventional analysis tools. CLKWorks is a breakthrough solution for variance-tolerant clock tree synthesis and optimization. Headquartered in Littleton, Mass., the company was founded by EDA industry veterans and has received $9 million in venture funding to date. More information can be found at www.clkda.com.
Amber is trademark of CLK Design Automation. All other trademarks or registered trademarks are property of their respective owners.
Contact:
For CLK Design Automationm Inc., Littleton
Laurie Stanley,
925-963-0410
Email Contact